Introduction to Power Standards The International Electrotechnical Commission (IEC) has developed standards for power supplies such as DC stabilized power standards: IEC 478.1-1974 "Director for DC Output Stable Power Supply"; IEC 478.2-1986 "DC Output Stable Power Supply Ratings and Performance"; IEC 478.3-1989 "Based Level and Measurement of Conducted Electromagnetic Interference from DC Output Stabilized Power Supply"; IEC 478.4-1976 "Test Method for DC Output Stabilized Power Supply Except Radio Frequency Interference"; IEC478.5-1993 "DC Output Measurement of the near-field magnetic field component of a stable power supply. This set of standards was promulgated and implemented earlier, and China's corresponding national standards have not yet been promulgated. The electronic industry standard SJ2811.1-87 "General DC stabilized power supply terminology and definition, performance and rating" for DC stabilized power supply, and SJ2811.2-87 "General DC stable power supply test method" have been released for 13 years. For a long time, these two standards have played a significant role in the research and production of DC stabilized power supplies in China. The International Electrotechnical Commission (IEC) promulgated IEC686-80 "AC Output Stable Power Supply" in 1980. The national standard GB/T "General Specification for AC Output Stable Power Supply" formulated with reference to this standard has been submitted for approval. The terminology in this standard, The technical requirements and test methods refer to IEC686. In addition, environmental testing requirements and test methods, quality assessment procedures, marking, packaging, transportation, storage and other requirements have been added to make it a guide to the development of AC power. A complete technical specification. In 1994, the former Ministry of Electronics Industry promulgated the electronic industry standard SJ/T10541-94 "General technical requirements for anti-interference AC power supply" and SJ/T10542-94 "Test method for anti-interference AC power supply", which consists of China Power Supply Association AC Stable Power Professional Committee and relevant domestic power supply manufacturers, testing institutions and other responsible for the preparation of technical requirements, environmental requirements and corresponding test methods and quality inspection rules for common and anti-interference AC power supplies. I have made detailed regulations. Since the implementation of this standard, it has been widely used in the field of AC voltage regulation technology. Other standards, such as the IEC443-1974 "Standard Power Supply for Measurement", China's Ministry of Electronics Industry Standard SJ/Z9035-87 "Standard Power Supply for Measurement" has also been applied within a certain range. In recent years, switching power supplies and uninterruptible power supplies have been developed in China, and China has also established corresponding national standards, such as GB/T14714-93 "General technical conditions for switching power supplies for micro-computer systems and equipment", GB/T14715-93 "Information Technology Equipment" The general technical conditions for uninterruptible power supplies, etc., are also widely used in related fields. The original four-machine standard SJ1670-80 "electronic equipment power terminology" has been around for 20 years, and many terms have been interpreted in contradiction with the current standards. Therefore, this year the Ministry of Information Industry Standardization organized the standard. The revision has retained some of the terms still applicable in the original standard, and the classification method of the standard has been greatly adjusted. The purpose of this revision standard is to enhance the applicability of the standard. Therefore, we are most commonly used in the field of modern power supply. Several types of power sources are classified, and their respective terms and definitions are given. The general part is a separate chapter. The terms and definitions in each chapter refer to the corresponding international standards and national standards. The standard is reported at the end of this year.
1
1
A manual pulse generator (MPG) is a device normally associated with computer numerically controlled machinery or other devices involved in positioning. It usually consists of a rotating knob that generates electrical pulses that are sent to an equipment controller. The controller will then move the piece of equipment a predetermined distance for each pulse.
The CNC handheld controller MPG Pendant with x1, x10, x100 selectable. It is equipped with our popular machined MPG unit, 4,5,6 axis and scale selector, emergency stop and reset button.
Manual Pulse Generator,Handwheel MPG CNC,Electric Pulse Generator,Signal Pulse Generator
Jilin Lander Intelligent Technology Co., Ltd , https://www.jllandertech.com