In the products produced by LED technology, there will be more or less output ripple, which is not conducive to the final efficiency of the product, so the designer needs to suppress it during the production process. This article will be for everyone. Introduce and explain how to reduce the ripple of LED output.
The output ripple is not difficult to understand. It refers to the AC component superimposed on the DC stability during the DC power output. From the perspective of the oscilloscope, you will see a slight fluctuation in voltage up and down, just like water marks, so it is called ripple. There are several ways to suppress or reduce it:
Increase inductance and output capacitance filtering
According to the formula of the LED driving power supply, the current fluctuation in the inductor is inversely proportional to the inductance value, and the output ripple is inversely proportional to the output capacitance value. Therefore, increasing the inductance value and output capacitance value can reduce the ripple.
Output ripple vs. output capacitance: vripple=Imax/(Co&TImes;f). It can be seen that increasing the output capacitor value can reduce the ripple.
As a general rule, for output capacitors, aluminum electrolytic capacitors are used to achieve high capacity. However, the electrolytic capacitor is not very effective in suppressing high-frequency noise, and the ESR is also relatively large, so a ceramic capacitor is connected in parallel with it to compensate for the shortage of the aluminum electrolytic capacitor.
At the same time, when the LED driving power supply is working, the voltage Vin at the input terminal does not change, but the current changes with the switch. At this point, the input power supply does not provide a good current, usually near the current input (in the case of the BucK type, which is near SWITcH), and a parallel capacitor is used to supply current.
Add a primary LC filter
The LC filter has a significant effect on the suppression of the noise ripple. The filter circuit is formed by selecting an appropriate inductor and capacitor according to the ripple frequency to be removed, and the ripple is generally reduced. However, in this case, it is necessary to consider the sampling point of the feedback comparison voltage.
The sampling point is selected before the LC filter (Pa) and the output voltage is reduced. Because any inductor has a DC resistance, when there is a current output, there will be a voltage drop across the inductor, causing the output voltage of the power supply to drop. And this voltage drop is a function of the output current.
LED drive power output followed by LDO filter
This is the most effective way to reduce ripple and noise. The output voltage is constant and there is no need to change the original feedback system, but it is also the most expensive and highest power method. Any LDO has an indicator: the noise rejection ratio.
After the LDO, the ripple is generally below 10mV.
On the diode and capacitor C or RC
Parasitic parameters should be considered when the diode is turned on and off at high speed. During diode reverse recovery, the equivalent inductance and equivalent capacitance become an RC oscillator, producing high frequency oscillations. In order to suppress this high frequency oscillation, a capacitor C or RC buffer network is connected in parallel across the diode. The resistance is generally 10Ω-100Ω, and the capacitance is 4.7pf-2.2nf.
The capacitance C or RC connected in parallel on the diode is determined by trial and error. If improperly chosen, it will cause more serious oscillations.
Diode followed by inductor (EMI filter)
This is also a common method of suppressing high frequency noise. Selecting a suitable inductive component for the frequency at which noise is generated can also effectively suppress noise. It should be noted that the rated current of the inductor should meet the actual requirements.
Through the above introduction, I believe that everyone has their own understanding of the suppression methods of output ripple in these several LED designs. These methods are not the most comprehensive, and are sufficient for the current general design requirements. In terms of noise suppression, the most important thing for designers is to find the right method from the perspective of self, from the aspects of volume and cost.
The above are some common methods for reducing output ripple in LED design. Although it may not be comprehensive, it is sufficient for general applications. Regarding noise suppression, not all of them are actually applied. It is important to choose the appropriate method according to your own design requirements, such as product volume, cost, development cycle, etc.
Linear Stepper Motor,Linear Actuator Motor,Nema Stepper Motor,Linear Drive Motor
Changzhou Sherry International Trading Co., Ltd. , https://www.sherry-motor.com