How to use the drop hammer impact tester? -Huaqiang Electronic Network

Probe domestic switch needle KG-300K needle head diameter is 3.0mm normally open switch needle

MOS power IC full range

Manufacturers produce direct sales LED lamp bead patch lighting products 0805 white light super bright indicator light dedicated

5050 Orange Light Orange Light Orange LED Bead 5050 Light Source Amber Amber Light Orange

How to use the drop hammer impact tester?

Drop hammer impact tester use:

1,

According to the test requirements, determine the mass of the hammer and the impact height, and prepare the sample for use.

2,

Determine the mass of the hammer

2.1

Correct

R5

×

19

,

R10

×

19

,

R25

×

19

,

R30

×

19

,

R50

×

25

(aluminum,

40cr

Mixed into) hammer head

A

Hammer

+

Hammerhead

+

Nut

=0.50kg
B

Hammer

+

Hammerhead

+

Nut

=1.75kg

C

Hammer

+

Hammerhead

+

Hammer

+

Nut

=9.50kg

The weights are shown in the table below:

quality

Kg

Quantity

quality

Kg

Quantity

0.100 1 0.500 1
0.125 1 1.000 1
0.200 1 2.000 2
0.250 1 3.000 1

Matching of hammer mass

:

Hammer mass in

0.5~1.75kg

,

A

Hammer

+

Hammerhead

+

Nut

+

Weight

Hammer mass in

1.75~10.25kg

,

B

Hammer

+

Hammerhead

+

Nut

+

Weight

Hammer mass in

10.25~16.00kg

,

C

Hammer

+

Hammerhead

+

Hammer

+

Nut

+

Weight

Example: Hammer mass

4.0kg

4.00=1.75kg

(

B

Hammer

+

Hammerhead

+

Nut)

+0.25 (

Weight

)+2.00

(weight);

Hammer mass

12.5kg

12.50=9.50kg

(

C

Hammer

+

Hammerhead

+

Nut)

+3.00

(weight)

2.2

for

R50

×

90

Steel hammer

A

Hammer

+

Hammerhead

+

Nut

=1.25kg
B

Hammer

+

Hammerhead

+

Nut

=2.50kg
C

Hammer

+

Hammerhead

+

Hammer

+

Nut

=10.25kg
2.3

Need to use

R50

×

90

Aluminum hammer head,

1kg

When quality impact is used, it should be selected

A

Hammer

+R50

×

90

Aluminum hammer

+

Nut

=1.00kg
2.4

Need to use

0.25kg

Should be selected when hammer impact

0

Hammer

+R50

×

25 (

Aluminum

)

Hammerhead

+

Round nut

=0.25kg

Hammer

3,

Put the hammer rod out of the sliding sleeve under the hammer seat, and place the selected weight on the hammer rod and tighten the nut.

4,

Turn on the power and enter the working state.

5,

Press the "slow up" button to lift the hammer off the bottom and press the "stop" button to facilitate the installation of the sample.

6,

Open the test chamber door and place the sample

V

Type on the iron.

7,

Observe the status of the left photoelectric switch red indicator light: Off indicates that the sample is too high to pass the light. The light indicates that the sample is low, the light can pass, and the lifting hand wheel is adjusted so that the center of the sample and the center of the phototube are on the same level.

8 ,

Determine the height zero point: use the "slow drop" and "slow rise" keys to make the hammer just touch the sample and adjust the height of the scale so that the pointer is just at the scale.

0

”

Point.

9 ,

Close the protective net and door, press the “fast up” button, the ruler indicates the lifting height, and press the “stop” button after rising to the predetermined height.

10.

Impact: first press the “pre-drop hammer” button to make the indicator light on this button light, then press the “drop hammer” button, the hammer body will fall and impact the sample. Note: Press the “pre-drop hammer” button: the button stop indicator does not light, indicating that the sample is too high, and the sample height needs to be re-adjusted. “Pre-drop hammer” button: Press this button to enter the pre-drop hammer state (after the sample is installed), press the “drop hammer” button, the hammer body will drop immediately, press other buttons to release the drop hammer state.

11,

When the hammer impacts the sample and the sample is not broken to cause the hammer to rebound, the photoelectric signal control hammer mechanism quickly clamps the rebound hammer body to achieve the purpose of preventing secondary impact.

12.

Press the "Fall and Drop" button, the pin on the hammer seat is inserted into the solenoid valve seat, and the micro switch is pressed down to stop.

13,

By number

2

Step, take out the sample, put in a new sample, repeat the steps, and perform some adjustment and inspection work in the middle.

14,

Shutdown: Turn off the power box power switch and the main power supply.